3800 wiki

User Tools

Site Tools

Trace:
transmissions:aftermarket:t56

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
transmissions:aftermarket:t56 [2021/07/02 14:38] – [Other requirements] bentransmissions:aftermarket:t56 [2022/01/25 17:22] (current) – [Expected Cost Breakdown] ben
Line 20: Line 20:
 Of course there are lots of examples of people using these transmissions with over 1,000 ft-lbs of torque without issue.\\ Of course there are lots of examples of people using these transmissions with over 1,000 ft-lbs of torque without issue.\\
 In general these transmissions are considered bulletproof unless it is being abused or if it has a lot of miles on it. In general these transmissions are considered bulletproof unless it is being abused or if it has a lot of miles on it.
- 
  
 ====== How to make it work ====== ====== How to make it work ======
Line 39: Line 38:
 Again, you will need to do your homework though here. This has not been documented very well yet. Again, you will need to do your homework though here. This has not been documented very well yet.
  
-==== Bellhousing  Adapter Option ====+==== Bellhousing Adapter Option ====
  
 The other option is to use the LS style bellhousing and an adapter plate between the bellhousing and the engine.\\ The other option is to use the LS style bellhousing and an adapter plate between the bellhousing and the engine.\\
Line 50: Line 49:
  
 You will also use the 3800/T5 or LS/T56 hydraulic slave cylinder (both are the same)\\ You will also use the 3800/T5 or LS/T56 hydraulic slave cylinder (both are the same)\\
-The slave cylinder will need a 1/2" spacer between it and the transmission to make up for the space used by the adapter plate.+The slave cylinder will need about a  1" spacer between it and the transmission to make up for the space used by the adapter plate.
  
 Some sites recommend using an adjustable clutch master cylinder as well. Some sites recommend using an adjustable clutch master cylinder as well.
Line 65: Line 64:
  
 If you're going down this route though you probably have a pretty good idea of what you're getting into already. If you're going down this route though you probably have a pretty good idea of what you're getting into already.
- 
  
 ===== Expected Cost Breakdown ===== ===== Expected Cost Breakdown =====
  
-|<font 11pt/Calibri,sans-serif;;black;;inherit>Part</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>where to find?</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>expected price</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>other info</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>Part</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>where to find?</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>expected price</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>other info</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>T56 Magnum Transmission</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit, Jegs, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$3500</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Any T56 should bolt up depending on what car you're putting it into. F-body LS1 T56 is kind of the standard though</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>T56 Magnum Transmission</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit, Jegs, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$3500</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Any T56 should bolt up depending on what car you're putting it into. F-body LS1 T56 is kind of the standard though</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>LS Engine → T56 bellhousing</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit, jegs, junkyard, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$300</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>All LS bellhousings should be similar…</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>LS Engine → T56 bellhousing</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit, jegs, junkyard, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$300</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>All LS bellhousings should be similar…</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>Malwood Adapter plate</font>   |[[https://malwoodauto.com.au/product/mwaengbel005-holden-v6-3-8l-to-suit-tremec-t56-with-ls1-bellhousing/|Malwood]]  |<font 11pt/Calibri,sans-serif;;black;;inherit>$450</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>price is shipped to USA after currency exchange rates</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>Malwood Adapter plate</font>   |[[https://malwoodauto.com.au/product/mwaengbel005-holden-v6-3-8l-to-suit-tremec-t56-with-ls1-bellhousing/|Malwood]]  | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$450</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>price is shipped to USA after currency exchange rates</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>LS1 clutch slave cylinder</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>OEM replacement or aftermarket</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$60</font>   | | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>LS1 clutch slave cylinder</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>OEM replacement or aftermarket</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$60</font>   | | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>LS1 clutch slave cylinder 1/2" spacer</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$100</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>ram-78511</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>LS1 clutch slave cylinder 1" spacer</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$100</font>   |   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>new pilot bearing</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>OEM replacement</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$25</font>   | | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>new pilot bearing</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>OEM replacement</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$25</font>   | | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>97-02 f-body 3800 clutch and flywheel</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Spec or OEM replacement</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$200 - $600</font>   | | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>97-02 f-body 3800 clutch and flywheel</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Spec or OEM replacement</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$200 - $600</font>   | <font inherit/Arial,Helvetica,sans-serif;;inherit;;inherit>Can also get a custom twin disc from Monster or Spec if you're willing to pay for it</font> | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>shifter</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>summit, jegs, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$40 - $300</font>   | | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>shifter</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>summit, jegs, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$40 - $300</font>   | | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>adjustable master cylinder</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>summit, jegs, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$200</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>May not be necessary, but can make sure the clutch works perfectly</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>adjustable master cylinder</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>summit, jegs, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$200</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>May not be necessary, but can make sure the clutch works perfectly</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>reverse lockout pigtail</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit, jegs, junkyard, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$20</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>ACDelco 12101857</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>reverse lockout pigtail</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit, jegs, junkyard, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$20</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>ACDelco 12101857</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>reverse light pigtail</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit, jegs, junkyard, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$10</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>ACDelco 12085485</font>   | +| <font 11pt/Calibri,sans-serif;;inherit;;inherit>reverse light pigtail</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit, jegs, junkyard, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$10</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>ACDelco 12085485</font>   | 
-|<font 11pt/Calibri,sans-serif;;black;;inherit>31 spine slip yoke (only for Magnum T56)</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>Summit, jegs, etc.</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>$70</font>   |<font 11pt/Calibri,sans-serif;;black;;inherit>If you don't already have a 31 spline slip yoke on your driveshaft. check your ujoint too because there's a few options</font>   |+| <font 11pt/Calibri,sans-serif;;inherit;;inherit>31 spine slip yoke (only for Magnum T56)</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>Summit, jegs, etc.</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>$70</font>   | <font 11pt/Calibri,sans-serif;;inherit;;inherit>If you don't already have a 31 spline slip yoke on your driveshaft. check your ujoint too because there's a few options</font>   |
  
 ---- ----
  
-Other sources I still need to comb through:+Other sources to look at: 
 + 
 +https://www.thechicagogarage.com/threads/3800-t56-swap-guide.177394/
  
 [[https://forums.justcommodores.com.au/threads/vt-v6-6-speed.229878/|https://forums.justcommodores.com.au/threads/vt-v6-6-speed.229878/]] [[https://forums.justcommodores.com.au/threads/vt-v6-6-speed.229878/|https://forums.justcommodores.com.au/threads/vt-v6-6-speed.229878/]]
Line 92: Line 92:
 \\ \\
 Cost Cost
- 
-\\ 
  
  
transmissions/aftermarket/t56.1625236704.txt.gz · Last modified: 2021/07/02 14:38 by ben