Block and Timing Cover
| Location | Thread Size, Length, and count |
| Main bearing cross-bolts | M8x1.25 @ 50mm (6x) |
| Oil pan to block | 1/4-20 @ 1“ (20x) |
| Timing cover to block bolts | 5/16-18 @ 3.125” (6) - - @1.5“ (4) |
| A/C bracket and RWD Motor mount bolts | M12x1.75 @ 35mm (3) |
| Starter motor | M10x1.5 @ 50mm (1) - - @ 115mm (1) |
| Battery cable to block | M10x1.5 @ 20mm (1) |
| EGR to block | 3/8-16 @ 1” (2) |
| Engine bracket to block | M10x1.5 @ 70mm (1) - - @ 75mm (1) - - M12x1.75 @ 130mm (1) |
| Power steering to block (bracket) | M8x1.25 @ 75mm (2) |
| Power bracket to block ('00+) | M8x1.25 @ 80mm (1) - - @ 25mm (2) |
| Oil filter bracket to timing cover | 5/16-18 @ 1.5“ (4) |
| water pump bolts | 1/4-20 @ 1.125” (4) - - 5/16-18 @ 3“ (4) |
| Cam sensor bolt | 1/4-20 @ 5/8” (1) |
| Flexplate to crank (auto trans cars) | 5/16-18 @ (1/2“?, 5/8”?, or 3/4“?) (8) |
| Flywheel to crank (manual trans only) | 5/16-18 @ 7/8” (8) |
| Pressure plate to Flywheel (manual trans only) | M8x1.25 @ 22mm (6) |
| Oil level sensor thread size | M20x1.5 |
| Bellhousing bolts | M12x1.75 @ ?? |
Heads
| Location | Thread Size, Length, and count |
| Valve cover bolts | 1/4-20 @ 5/16“x5/8” shoulder (12) |
| Header to head bolts | 5/16-18 @ 1“ (9x) - - @ 1.5” (3x) |
| engine lift bracket to block | 5/16-18 @ 5/8“ (2) |
| Intake manifold to head bolts | 5/16-18 @ 1.125” (12) |
| EGR to manifolds | M6x1 @ 25mm (2) |
Intake/Supercharger
| Location | Thread Size, Length, and count |
| Supercharger to LIM | M8x1.25 @ 40mm (9) - - @ 60mm (1) - - @ 80mm (1) |
| SC snout to SC | M8x1.25 @ 50mm (9) |
| Bracket to TB | M6x1 @ 20mm (2) |
| PCV Cover to SC | M6x1 @ 16mm (2) |
| Vac port to SC | M6x1 @ 20mm (2) |
| SC bypass valve to SC | M6x1 @ 16mm (2) |
| Vac Tee to SC | M8x1.25 @ 20mm (2) |
| Fuel rail to SC | M8x1.25 @ 10mm (1) |
| Fuel rail to Intake | M6x1 nut (4) and stud |
| Thermostat cover | M8x1.25 @ 30mm (2) |
Sensors and Electronics
| Location | Thread Size, Length, and count |
| Sensors to throttle body | M4x0.7 @ 12mm (2) - - @16mm (4) |
| Ignition coil to control module | M5x0.8 @ 45mm (6) |
| Cam sensor bolt | 1/4-20 @ 5/8“ (1) |
| MAP sensor | M5x0.8 @ 30mm (2 or 4) |
| Starter solenoid enable nut | M5x0.8 nut |
Other Accessories
| Location | Thread Size, Length, and count |
| A/C bracket | 3/8-16 @ 2” (1) |
| Water pump pulley | M6x1 @ 12mm (4) |
| LIM water cover | M6x1 @ 20mm (2) |
| PCV cover | M8x1.25 @ 16mm (2) |
| Heater hose elbow brackets | M6x1 @ 16mm (2) |
| Evap Sensor bracket | M6x1 @ 16mm (1) |
| EGR heat shield | M6x1 @ 16mm (1) |
| Supercharger tensioner bracket | 3/8-16 @ 1.5“ (1) - - @ 2” (1) - - @ 2.5“ (1) |
| Main belt tensioner bracket | 3/8-16 @ 2.5” (3) |
| Passenger Side trans bracket | 3/8-16 @ 3/4“ (2) |
| Altenator | M10x1.5 @ 60mm (2) |
| A/C compressor to bracket | M10x1.5 @ 60mm (3) |
| Lower SC idler pulley | M10x1.5 @ 25mm (1) |
Most, if not all of this information has been gathered from Mattstrike's post on PBC